How to program remote for legacy garage door opener

All of these remote controls will work with the Code Dodger Legacy garage door openers. In addition, the Master Remote Control mentioned above can be programmed to work with Code Dodger Legacy garage door opener. However, if your Overhead Door Legacy garage door opener was manufactured between November and January , the remote controls shown above will not work.

Regardless of which series of Code Dodger CD Legacy opener you have installed there is only one 1 remote controls that will work. This remote control is a standard 3 button remote control part R. Part Number R. Order Remote Control part R. When trying to program R from the Code Dodger era of November to the end of , only the button farthest to the right will program. How to Reprogram Your Wayne Dalton Garage Door Openers Press and release the "Program" button on your garage door motor and the red indicator light will begin flashing for 30 seconds.

Select a four-digit code for your opener and enter the code on the keypad. Can I program my car garage opener without a remote? In most cases, your attempt to go through the process of how to program a HomeLink garage door opener without a remote will not work if the car door is open or the key is in the ignition. Because of this, the first thing you need to do is make sure the door is closed, and the key is out. How do I reprogram my genie Intellicode garage door opener? Once the Light is solid, press the Garage Opener Button again.

One more thing. The Tahoe has 3 buttons and each one has a light above it. Not sure if you need to know that. I tried to read through all the posts and may have missed it so sorry. I have a Marantec M opener and just bought a Chevy Tahoe. I can't for the life of me figure out how to program the Tahoe. Can you please help? Sweeps, thanks for your advice and help. It may be time for a new GDO. Hey Sweeps, thanks again for your help.

I tried your instructions, in fact it had been unplugged all night. I pushed and held donwn learn button yellow and round for 2o seconds little red light and nothing seems to happen. The red light stays on until I hit a remote button. I tried holding it less, more, rapidily. I programmed another remote for it that works but now the car fob opens and closes door, not only mine it seems to respond to neighbours also.

I tried to reset or clear it by holding button in, doesn't seem to do anything. Thank you in advance D. I haven't cleared the board yet, the thing is, I use a LM that works perfectly and bought a LM as a spare, since the is working I'm afraid that resseting the board will leave that remote useless and end up with two non working remotes. Hello, my liftmaster E only has en 'erase' button, which I poke but the LED indicator does not stay on, though I tried the instructions anyway but nothing happens, I can see the light blinking when I press the button on the control but is not operating the liftmaster.

The homelink in both my cars have stopped working. Both were working and then they just stopped. Unable to reprogram either of them. Completely reset the opener and the two cars then tried to reprogram them and all the other remotes. Can program the keypad and four remotes. Also, the light won't go out - neither automatically nor with the button.

I'm having trouble programming my GMC Traverses garage door opener remote to my Wayne Dalton quantum with a brown smart button can you tell me which remote I may need to purchase to get this to work thank you.

Everything has worked perfectly for several years. Recently I noticed that my homelink button controls my neighbor's garage door in addition to mine.

My standard remotes do not control the neighbor's door. Is this an issue I can resolve our does my neighbor need to change something on his opener? We have 2mercedes suv's. Can we reprogram the cars and a handheld at the same time. Can we wipe all thwe codes on the door opener and start over????? I have done this many times and even cleared all codes to make sure it wasn't full.

I have a new Tahoe, held in the vehicle button then had someone hit the smart button once. Even tried it by hitting the smart button then holding the Vehicle button but still nothing. I reprogrammed the key pad on the house and it works fine?

Hi I just bought a genie garage door opener modle number trying to program my acura to the garage opener where is the learn button thanks. I have a genie silent max trying to program to my Nissan Quest when training to remote light flashes slow and then goes completely off on both of my cars what am I doing wrong. Tried programming the second door - held the garage door opener button and pressed the second button and it didn't program the car - instead it programmed the remote to open both the main door and 2nd door now from the same button on the same remote external - We weren't trying to mess with the main door at this point..

Quick add to just submitted after re-reading the previous answered Q and it's reference to holding 5. It seems every time I press the learn to program any remote, all the others are now off channel and won't work.

I understand how to program remotes although reading your post, in frustration I may have held the learn button in to long - but it still seems to work. My problem is programming more than one remote at a time. Some are not always here - or here together. Even then, trying to program 2 or 3 - plus the keypad Obviously it is a run to the keypad - and this all happens any time I may want to change Pins - even for the temporary feature.

After a year and a half after buying my new car, I finally was able to get the car's universal remote to work - thanks to you!! I've just purchased an '07 VW Touareg and cannot program the Genie opener to the vehicle.

Is there an issue with Intellicode 1 or 2 with this vehicle? Does this have any effect? The car manufacturer's manual mentions that the Homelink system is compatible with 'most' openers. It is an older Genie garage opener and I wonder if it's reached its capacity for remotes - 5? We had no problem with the Ford, this is frustrating - any help or guidance would be very much appreciated. I press the learn button before I read anything!

So from reading your info, I must have erase the codes? My hand remote still works. I am trying to program my wife new car.

We follow the car Manuel , but it is not working! Can you help? I have a Stanley Model opener without a programing button on the door unit. The LED learn indicator light on the power head should stop blinking and stay solid on. Press and then release the garage door remote button a second time. The LED learn indicator light on the power head should go out. The garage door remote should now be programmed.